Template:Infobox connector
D4 Video connector | ||||
---|---|---|---|---|
| ||||
This example is not factual - it is purely illustrative of the infobox. | ||||
Type | Analogue video connector | |||
Production history | ||||
Designer | Some guy | |||
Designed | Early 1990s | |||
Manufacturer | Initially Toshiba | |||
Produced | Early 1990s to 2005 | |||
Superseded | RF connector | |||
Superseded by | DVI connector (2005) | |||
Specifications | ||||
Length | 36 mm (typical) | |||
Width | 25 mm | |||
Height | 6.5 mm | |||
Hot pluggable | Yes | |||
External | External | |||
Electrical | 220 volts AC 50 Hz typically | |||
Earth | Dedicate pin | |||
Max. voltage | 450 volts peak | |||
Max. current | 20 amps at 220 volts, 5 amps at 400 volts | |||
Audio signal | None | |||
Video signal | Analogue 480i, 480p, 720p, 1080i | |||
Data signal | Resolution and Aspect ratio only | |||
Width | 2 bits | |||
Bandwidth | 120 bit/s | |||
Max. devices | 1 | |||
Protocol | Serial | |||
Cable | 14 core shielded (25 m max) | |||
Pins | 14 (6 video, 3 reserved, 2 detect, 3 data) | |||
Connector | DB-25 | |||
Pin out | ||||
A male connector seen from the front. | ||||
Spec name | Example col title | |||
Pin 1 | Y | luminance (0.7 V, 75 Ω) | ||
Pin 2 | Y GND | Y ground | ||
Pin 3 | Pb | 0.35 V, 75 Ω | ||
Pin 4 | Pb GND | |||
Pin 5 | Pr | 0.35 V, 75 Ω | ||
Pin 6 | Pr GND | |||
Pin 7 | Reserve link 1 | |||
Pin 8 | Data line 1 | 0V = 525 lines 2.2 V = 750 lines 5V = 1125 lines | ||
Pin 9 | Data line 2 | 0V = 59.94i / 60i 5 V = 59.94p / 60p | ||
Pin 10 | Reserve link 2 | |||
Pin 11 | Data line 3 | 0V = 4:3 2.2V = 4:3 letterbox 5V = 16:9 | ||
Pin 12 | Plug insert detect ground | |||
Pin 13 | Reserve link 3 | |||
Pin 14 | Plug insert detect | output 10 kΩ, input > 100 kΩ | ||
Hooks | GND | Shell ground | ||
These are some notes about the pinout of this connector. The pins are razor sharp. |
Connector Infobox is an infobox for electrical and (audio/video) signal connectors of all kinds.
Notes
The template supports 3 images:
- image, logo, pinout_image
Image and logo share a 300px wide area - so if both are used then the width of the image should be set to 150px i.e. [[Image:example.jpg|150px]]. If only image and pinout are used, then the size of both should be 300px.
Parameters and usage
{{Infobox connector |name = |type = |image = |logo = |caption = |designer = |design_date = |manufacturer = |production_date = |superseded = |superseded_by = |superseded_by_date = |external = |hotplug = |length = |width = |height = |electrical = |ground = |maximum_voltage = |maximum_current = |audio_signal = |video_signal = |data_signal = |data_bit_width = |data_bandwidth = |data_devices = |data_style = |cable = |physical_connector = |num_pins = |pinout_col1_name = |pinout_col2_name = |pinout_image = |pinout_caption = |pin1 = |pin1_name = |pin2 = |pin2_name = |pin3 = |pin3_name = |pin4 = |pin4_name = |pin5 = |pin5_name = |pin6 = |pin6_name = |pin7 = |pin7_name = |pin8 = |pin8_name = |pin9 = |pin9_name = |pin10 = |pin10_name = |pin11 = |pin11_name = |pin12 = |pin12_name = |pin13 = |pin13_name = |pin14 = |pin14_name = |pin15 = |pin15_name = |pin16 = |pin16_name = |pin17 = |pin17_name = |pin18 = |pin18_name = |pin19 = |pin19_name = |pin20 = |pin20_name = |pin21 = |pin21_name = |pin22 = |pin22_name = |pin23 = |pin23_name = |pin24 = |pin24_name = |pin25 = |pin25_name = |pin26 = |pin26_name = |pin27 = |pin27_name = |pin28 = |pin28_name = |pin29 = |pin29_name = |pin30 = |pin30_name = |pin31 = |pin31_name = |pin_custom1_name = |pin_name_custom1 = |pin_custom1 = |pin_custom2_name = |pin_name_custom2 = |pin_custom2 = |pin_custom3_name = |pin_name_custom3 = |pin_custom3 = |pin_custom4_name = |pin_name_custom4 = |pin_custom4 = |pin_custom5_name = |pin_name_custom5 = |pin_custom5 = |pin_custom6_name = |pin_name_custom6 = |pin_custom6 = |pin_custom7_name = |pin_name_custom7 = |pin_custom7 = |pin_custom8_name = |pin_name_custom8 = |pin_custom8 = |pinout_notes = }}
The above documentation is transcluded from Template:Infobox connector/doc. (edit | history) Editors can experiment in this template's sandbox (create | mirror) and testcases (create) pages. Please add categories to the /doc subpage. Subpages of this template. |